The article author is making several good observations related to Tools You Need to Install a New Bathtub in general in the article directly below.
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough job. If the old bathtub is conveniently available, the job can move immediately; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will need a helper to vacate the old tub as well as set in the brand-new one. Ensure you have actually qualified yourself for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will certainly assist you mount a new bath tub in your bathroom if you have actually already gotten a new bathtub as well as don't need to alter the setup of your previous water supply pipes.
Your devices as well as material list must comprise the following:
Planning for the Installation
To start with, the supporting framework provided with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the limited accessibility that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, position the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub until the spirit level checks out level.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water system and also inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill the tub as well as additionally check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the tub should wait up until the bath tub has actually been used a minimum of once as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washers remain in place between the tap and the sink. Protect the faucet in position with the supplier offered backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing complications with dampness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack relatively very early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the market. It is recommended to fit the tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very curious about Tools You Need to Install a New Bathtub and I am assuming you enjoyed reading the new blog post. Do you know someone else who is enthusiastic about A Step-by-Step Guide to Installing a Bathtub? Do not hesitate to share it. Bless you for your time. Visit us again soon.
Trusted plumbing solutions at hand.